2015年5月6日 (三) 11:52 Hovercool

2015-05-06T11:52:28Z

新页面

= 配置lcm背光的控制脚 =

lcm背光控制主要有两个引脚：使能脚EN和亮度控制引脚VFB。使能脚用来控制背光的使能与否，比如这里是1为enable，0为disable；亮度控制引脚则是用来接PWM输出，通过PWM的占空比来控制背光亮度，这里是低为亮，高为灭。

所以在这两个引脚的连接和配置上要保证EN连接至gpio上，而VFB则连接至BB的PWM输出口，然后通过dct工具将上述引脚配置成对应的mode。

= 配置uboot =

== mediatek/custom/bbk75_ics/uboot/cust_leds.c ==

在 cust_led_list数组中更改 lcd-backlight的配置为pwm：
<pre class="prettyprint">
static struct cust_mt65xx_led cust_led_list[MT65XX_LED_TYPE_TOTAL] = {
...
//{"lcd-backlight", MT65XX_LED_MODE_CUST, (int)DISP_SetBacklight,{0}},
{"lcd-backlight", MT65XX_LED_MODE_PWM, PWM1,{0}},
};
</pre>

== mediatek/platform/mt6575/uboot/mt65xx_leds.c ==

在 mt65xx_led_set_cust中添加对lcm使能脚的控制，以更好地对屏幕的亮灭进行控制：
<pre class="prettyprint">
...
case MT65XX_LED_MODE_PWM:
if(strcmp(cust->name,"lcd-backlight") == 0)
{
if(level == 0)
{
mt_set_gpio_out(BACKLIGHT_EN_PIN,GPIO_OUT_ZERO);

}else
{
if (level < 80) level =80;
level = level/4;
brightness_set_pwm(cust->data, level,&(cust->config_data));
udelay(10000);
mt_set_gpio_out(BACKLIGHT_EN_PIN,GPIO_OUT_ONE);
}

//return brightness_set_pwm(cust->data, level,&cust->config_data);
}
else
{
return led_set_pwm(cust->data, level);
}
return 1;
case MT65XX_LED_MODE_GPIO:
...
</pre>

以下两个函数同步更改：
<pre class="prettyprint">
void mt65xx_backlight_on(void)
{
printf("[LEDS]uboot: mt65xx_backlight_on \n\r");
mt_set_gpio_mode(BACKLIGHT_EN_PIN, GPIO_MODE_00);// GPIO MODE
mt_set_gpio_dir(BACKLIGHT_EN_PIN, GPIO_DIR_OUT);
mt_set_gpio_out(BACKLIGHT_EN_PIN, GPIO_OUT_ONE);
mt65xx_leds_brightness_set(MT65XX_LED_TYPE_LCD, LED_FULL);
}

void mt65xx_backlight_off(void)
{
printf("[LEDS]uboot: mt65xx_backlight_off \n\r");
mt_set_gpio_mode(BACKLIGHT_EN_PIN, GPIO_MODE_00);// GPIO MODE
mt_set_gpio_dir(BACKLIGHT_EN_PIN, GPIO_DIR_OUT);
mt_set_gpio_out(BACKLIGHT_EN_PIN, GPIO_OUT_ZERO);
mt65xx_leds_brightness_set(MT65XX_LED_TYPE_LCD, LED_OFF);
}
</pre>

= 配置kernel =

== mediatek/custom/bbk75_ics/kernel/leds/mt65xx/cust_leds.c ==

将背光led的控制方式更改为pwm：
<pre class="prettyprint">
static struct cust_mt65xx_led cust_led_list[MT65XX_LED_TYPE_TOTAL] = {
...
///{"lcd-backlight", MT65XX_LED_MODE_CUST, (int)Cust_SetBacklight,{0}},
{"lcd-backlight", MT65XX_LED_MODE_PWM, PWM1,{0}},
};
</pre>

== mediatek/source/kernel/drivers/leds/leds.c ==

和uboot一样，在 mt65xx_led_set_cust中添加对lcm使能脚的控制，以更好地对屏幕的亮灭进行控制：
<pre class="prettyprint">
if (level > LED_FULL)
level = LED_FULL;
else if (level < 0)
level = 0;
mt_set_gpio_mode(BACKLIGHT_EN_PIN, GPIO_MODE_GPIO);
mt_set_gpio_dir(BACKLIGHT_EN_PIN, GPIO_DIR_OUT);
mt_set_gpio_mode(BACKLIGHT_VFB_PIN, GPIO_MODE_01);
mt_set_gpio_dir(BACKLIGHT_VFB_PIN, GPIO_DIR_OUT); //GPIO_PWM_1_PIN_M_PWM

printk("mt65xx_leds_set_cust: set brightness, name:%s, mode:%d, level:%d\n",
cust->name, cust->mode, level);
switch (cust->mode) {
case MT65XX_LED_MODE_PWM:
if(strcmp(cust->name,"lcd-backlight") == 0)
{
bl_brightness = level;
if(level == 0)
{
mt_set_gpio_out(BACKLIGHT_EN_PIN,GPIO_OUT_ZERO);
mt_set_pwm_disable(cust->data);
mt_power_off (cust->data);
}else
{
level = brightness_mapping(tmp_level);
if(level > 0 && level < 20 ) level = 20;//45
if ( level < 195 )
{
level=(level-20)/7;
}
else
{
level=level - 20 ;
level=(level-175)/4;
level=level+25;
}
if (level > 244 && level < 255) level =244; //level 37
//if (level > 54) level = 54;
backlight_set_pwm(cust->data, level, bl_div,&(cust->config_data));
mt_set_gpio_out(BACKLIGHT_EN_PIN,GPIO_OUT_ONE);
}
bl_duty = level;

}else
{
if(level == 0)
{
led_tmp_setting.nled_mode = NLED_OFF;
}else
{
led_tmp_setting.nled_mode = NLED_ON;
}
led_set_pwm(cust->data,&led_tmp_setting);
}
return 1;

case MT65XX_LED_MODE_GPIO:
</pre>

= 注意事项 =

如果uboot中将VFB配置成了gpio并且输出低使背光一直保持全亮，在进入kernel后通过代码再将其设置为pwm模式，这理应是ok的；但现实就是不行，这样会导致背光不能调节（不过由于没有量波形，故不知是有波形输出还是仍一直输出低电平），就在这里耗时较长，所以关注一下这点。

附修改记录：
<pre>
Modified : /trunk/ALPS.ICS.MP.V1_T_20120405/mediatek/custom/bbk15_td_ics/kernel/leds/mt65xx/cust_leds.c
Modified : /trunk/ALPS.ICS.MP.V1_T_20120405/mediatek/custom/bbk15_td_ics/uboot/cust_leds.c
Modified : /trunk/ALPS.ICS.MP.V1_T_20120405/mediatek/platform/mt6575/uboot/mt65xx_leds.c
Modified : /trunk/ALPS.ICS.MP.V1_T_20120405/mediatek/source/kernel/drivers/leds/leds.c
</pre>

MTK6515 配置lcd背光 - 版本历史

2015年5月6日 (三) 11:52 Hovercool